Disto Support » Uncategorized http://oldappr.globalwebsupply.com/support from AppraisersLaser.com Wed, 26 Apr 2017 13:20:34 +0000 en-US hourly 1 http://wordpress.org/?v=3.5.1 Disto Error Codes http://oldappr.globalwebsupply.com/support/disto-error-codes/ http://oldappr.globalwebsupply.com/support/disto-error-codes/#comments Tue, 01 Apr 2014 16:54:15 +0000 admin http://www.appraiserslaser.com/support/?p=294 Continue reading →]]>
Error  Code
Description
Solution
154
Transverse tilt >20°
Hold the instrument without any transverse tilt
156
Transverse tilt > 10°
Hold the instrument without any transverse tilt
160
Main tilt direction, angle too high (>45°)
Measure angle up to +/- 45°
162
The calibration has not been
accomplished on a leveled
surface and the calibration value
is respecitvely within an ineligible
area.
Calibrate the device on an absolute
horizontal leveled surface.
203
Wrong measuring sequence for Pythagoras measurements
Measure in correct sequence
204
Calculation error
Repeat procedure
206
No endpiece detection
Attach the endpiece properly. If error still occurs, replace the endpiece
217

Measuring module error

Contact Us

240
Data transfer error
Repeat procedure
245
2nd button pressed although no
Bluetooth connection exists.
Establish Bluetooth connection
252
Temperature too high, above 50°C
Cool down the instrument
253
Temperature too low, below 0°C
Warm up instrument
255
Receiver signal too low, measuring time too long, distance too long
Use target plate, measuring time > 10 sec.
256
Receiver signal too strong
Use target plate (white side)
257
Erroneous measurement, too much   backlight
Use target plate
260
Laser beam was interrupted
Repeat measurement
272-276

 Measuring module error

279

 Measuring module error

Contact Us

285-291

 Measuring module error

Contact Us

297-299

 Measuring module error

Contact Us

402

 Measuring module error

Contact Us

404

 Measuring module error

Contact Us

501-503

 Measuring module error

Contact Us

651

 Measuring module error

Contact Us

801-803

 Measuring module error

Contact Us

]]> http://oldappr.globalwebsupply.com/support/disto-error-codes/feed/ 0 Lanyard / Hand Loop Installation http://oldappr.globalwebsupply.com/support/lanyard-hand-loop-installation/ http://oldappr.globalwebsupply.com/support/lanyard-hand-loop-installation/#comments Sun, 30 Mar 2014 14:55:45 +0000 admin http://www.appraiserslaser.com/support/?p=283 Continue reading →]]> All Leica Disto’s are included with a lanyard / hand-loop to prevent an accidental drop.

To install the lanyard:

lanyard-install-holes

1. Locate the 2 small holes near the base on left or right side (some units have these on both sides).

2. Squeeze the small loop at the end of the lanyard and push it into one of the holes. You may need to work it back-and-forth slightly until it comes out the second hole. It is sometimes easier if you can remove the battery door.

3. Loop the entire lanyard through the small loop and pull tight.

]]> http://oldappr.globalwebsupply.com/support/lanyard-hand-loop-installation/feed/ 0 Helpful Tips with Disto D5 http://oldappr.globalwebsupply.com/support/helpful-tips-with-disto-d5/ http://oldappr.globalwebsupply.com/support/helpful-tips-with-disto-d5/#comments Wed, 17 Apr 2013 14:53:39 +0000 admin http://www.appraiserslaser.com/support/?p=153


Helpful tips video on the Leica Disto D5
]]> http://oldappr.globalwebsupply.com/support/helpful-tips-with-disto-d5/feed/ 0